Motec ACL VIM Bedienungsanleitung Seite 79
- Seite / 99
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
MoTeC Appendices 75
ACL Errors
These errors are generated by the ACL communications system.
2 FRAMING Incorrect number of samples received.
256 BAD CONFIG Configuration mismatch between ACL
and device. Resend the configuration.
512 NO DATA VIMCOM packets have not been found.
Either there is a wiring fault or ACL
Connections is setup incorrectly.
2048 WRONG DATA VIMCOM packet has bad length.
4096 BUS WARNING More than 96 errors have occurred on
the CAN bus. Check wiring and
termination resistors. The CAN bus may
still be operational.
8192 BUS OFF More than 255 errors have occurred on
the CAN bus. CAN communications is
suspended when this error occurs.
Check wiring, termination resistors and
the CAN baud rate. Also check that CAN
HI and CAN LO are correct (not
swapped).
VIMCOM Device Errors.
These error codes are sent once by the VIMCOM device on resuming
data transmission and therefore indicate why data was previously not
being transmitted.
4097 STARTUP Device has restarted (normally due to
power up) Data is not sent until sync is
achieved.
4098 HALT Data not sent due to deliberate halt. For
example configuration or firmware being
sent.
4099 OVERRUN Data not sent due to transmit buffer
overrun (possibly due to CAN bus too
busy)
4100 SYNC TIMEOUT Data not sent due to ACL sync message
timeout (sync not received from ACL)
4101 CAN ERROR Data not sent due to error on CAN bus
- Contents 1
- Introduction 5
- Overview 6
- MoTeC Overview 3 7
- Measurement Devices 7
- Options 7
- Memory Card 7
- More Information 7
- PLM Lambda Meter 10
- Telemetry Radio System 10
- MoTeC Overview 7 11
- Operation 13
- Display 14
- Display Elements 15
- Centre Numeric Display 16
- 12 Operation 16
- Numeric Displays 16
- Display Modes 17
- 14 Operation 18
- Practice Mode 18
- Warm-up Mode 18
- Display Formatting 19
- Data Logging 20
- MoTeC Operation 17 21
- Memory Filling Options 21
- Logging Rate 21
- Retrieving the Logged Data 23
- Functions & Calculations 24
- Measurement Inputs 25
- Input Basics 26
- Input Types 27
- 24 Operation 28
- MoTeC Operation 25 29
- 26 Operation 30
- Auxiliary Outputs 31
- Communication Ports 31
- 28 Operation 32
- Serial Communications Ports 32
- ACL Central Logger 34
- ACL Setup 35
- ACL Firmware 35
- Connected Devices 36
- VIM Setup 37
- VIM Firmware 37
- ADL2 & SDL Display 38
- MDD Display 39
- BR2 Beacon Receiver 39
- SLM Shift Light Module 40
- E888 / E816 Expanders 41
- MoTeC GPS 42
- ECU Connection via RS232 44
- ECU Connection via CAN 44
- ECU Setup 45
- ACL Manager Software 47
- Mouse & Keyboard 48
- Main Menu 48
- Toolbar 49
- Online / Offline 49
- Configuration 49
- Configuration Files 50
- Changing the Configuration 51
- 48 ACL Manager Software 52
- Updating 52
- Matching Versions 52
- Configuration File Version 52
- Channels 54
- Channel List 55
- Channel Properties 55
- Selecting Channels 56
- Conditions Overview 58
- Checking Operation 59
- Sensor Zeroing 60
- Details Editor 60
- Windows Keyboard Use 61
- 58 Windows Keyboard Use 62
- Using the Selected Item 62
- Check Box 63
- Radio Buttons 63
- 60 Windows Keyboard Use 64
- Appendices 66
- MoTeC Appendices 63 67
- Telemetry Option 67
- Remote Logging Option 67
- Analogue Inputs 69
- 66 Appendices 70
- VIM Pull-up Resistor Pins 70
- VIM Speed Inputs 71
- 68 Appendices 72
- MoTeC Appendices 69 73
- E888/E816 73
- 70 Appendices 74
- Other Devices 74
- MoTeC Appendices 71 75
- Usage: 75
- Options: 75
- 72 Appendices 76
- MoTeC Appendices 73 77
- RS232 Errors 77
- General CAN Errors 77
- 74 Appendices 78
- "VIMCOM" Errors 78
- MoTeC Appendices 75 79
- 76 Appendices 80
- MoTeC Appendices 77 81
- 78 Appendices 82
- M800 / M880 82
- MoTeC Appendices 79 83
- M48, M4 (pre M4e) and M8 83
- Appendix K: CAN Bus Wiring 84
- Appendix L: Wire Information 85
- For 5 Pin 86
- MoTeC Appendices 83 87
- 84 Appendices 88
- VIM 5 Pin Connector 88
- VIM 55 Pin Connector 88
- MoTeC Appendices 85 89
- 86 Appendices 90
- MoTeC Appendices 87 91
- 88 Appendices 92
- MoTeC Appendices 89 93
- ACL 5 Pin Connector 93
- ACL 22 Pin Connector 93
- 90 Appendices 94
- MoTeC Appendices 91 95
- 92 Notes 96
- MoTeC Notes 93 97
- 94 Notes 98
- MoTeC Notes 95 99
Verwandte Produkte und Handbücher für Hardware Motec ACL VIM
Hardware Motec ADL3 EDL3 Bedienungsanleitung
(80 Seiten)
(80 Seiten)
Hardware Motec DBW-4 Bedienungsanleitung
(21 Seiten)
(21 Seiten)
Hardware Motec CDL3 Bedienungsanleitung
(86 Seiten)
(86 Seiten)
Hardware Motec C185 Bedienungsanleitung
(85 Seiten)
(85 Seiten)
Hardware Motec GPS-BL1 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Hardware Motec GPS-G1 Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Hardware Motec C125 Bedienungsanleitung
(89 Seiten)
(89 Seiten)
Hardware Motec E816 Bedienungsanleitung
(30 Seiten)
(30 Seiten)
Hardware Motec GPS-L10 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Hardware Motec Interpreter Bedienungsanleitung
(37 Seiten)
(37 Seiten)
Hardware Motec LTCN Bedienungsanleitung
(39 Seiten)
(39 Seiten)
Hardware Motec Knock OKM Bedienungsanleitung
(36 Seiten)
(36 Seiten)
Hardware Motec M8 Bedienungsanleitung
(63 Seiten)
(63 Seiten)
Hardware Motec M880 Bedienungsanleitung
(101 Seiten)
(101 Seiten)
Hardware Motec MDC Bedienungsanleitung
(22 Seiten)
(22 Seiten)
Hardware Motec M880 Bedienungsanleitung
(111 Seiten)
(111 Seiten)
Hardware Motec MDC2 Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Hardware Motec MDD Bedienungsanleitung
(48 Seiten)
(48 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.165 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern